{"id":3284,"date":"2024-08-29T16:31:18","date_gmt":"2024-08-29T11:01:18","guid":{"rendered":"https:\/\/study.madeeasy.in\/?p=3284"},"modified":"2025-07-16T15:00:05","modified_gmt":"2025-07-16T09:30:05","slug":"geometric-design","status":"publish","type":"post","link":"https:\/\/www.madeeasy.in\/study\/ce\/highway-engineering\/geometric-design","title":{"rendered":"Factors Affecting Geometric Design"},"content":{"rendered":"

There are certain basic design controls and criteria which govern the geometric features of a highway.<\/p>\n

    \n
  1. Topography<\/li>\n
  2. Design speed<\/li>\n
  3. Road user characteristics<\/li>\n
  4. Vehicle characteristics<\/li>\n
  5. Traffic (its volume, directional distribution and composition including the future estimates)<\/li>\n
  6. Traffic capacity<\/li>\n
  7. Environmental considerations<\/li>\n
  8. Economy in construction, maintenance and operation of vehicles<\/li>\n<\/ol>\n

    Camber or Cross Slope<\/h2>\n\n\n\n\n\n\n\n\n
    Camber for different road surfaces<\/th>\n<\/tr>\n
    Types of road surface
    \nRange of camber<\/th>\n    		Heavy Rainfall to light rainfall<\/th>\n<\/tr>\n
    Cement concrete and high type bituminous surface<\/td>\n1 to 50 (2.0%) to 1 in 60 (1.7%)<\/td>\n<\/tr>\n
    Thin bituminous surface<\/td>\n1 to 40 (2.5%) to 1 in 50 (2.0%)<\/td>\n<\/tr>\n
    Water bound macadam and gravel pavement<\/td>\n1 to 33 (3%) to 1 in 40 (2.5%)<\/td>\n<\/tr>\n
    Earth<\/td>\n1 to 25 (4.1%) to 1 in 33 (3.0%)<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

    Transverse slope provided to the road to drain off rain water from road surface is known as camber. It is measured in 1 in \u2018n\u2019 or n% (e.g. 1 in 50 or 2%). Main advantage of providing camber are quick drying of pavement which in turn increases safety and subgrade protection by drainage.<\/p>\n

    Requirement of camber of a pavement depends upon:<\/strong><\/h3>\n
      \n
    1. Type of pavement surface<\/li>\n
    2. The amount of rainfall<\/li>\n<\/ol>\n

      Camber may be provided in the shape of parabolic, elliptic or straight line shape. For cement concrete pavement, straight line camber is provided while parabolic and elliptic shape are preferred for fast moving vehicles because they require frequent crossing of crown line during overtaking operation.<\/p>\n

      \"Cross<\/p>\n

      The camber of shoulder should be atleast 0.5% steeper than the cross slope of adjoining pavement, subjected to a minimum of 3.0% and a maximum value of 5.0% for earth shoulder.<\/p>\n

      Disadvantages of excessive camber are:<\/h3>\n
        \n
      1. Transverse tilt of vehicle and discomfort<\/li>\n
      2. Formation of cross ruts or depression<\/li>\n
      3. Tendency of the vehicle to move along the centre line<\/li>\n<\/ol>\n

        Stopping Sight Distance<\/span><\/h3>\n

        Stopping sight distance is the minimum distance over which the driver travelling at design speed can apply brakes and bring the vehicle to stop position safely without having collision with any other obstruction. It is also known as minimum sight distance or non passing sight distance. Stopping sight distance should be provided throughout the length of all roads.<\/p>\n

        Stopping sight distance composed of two components: (i.e. lag distance and braking distance)<\/p>\n

        (i) Lag Distance (d):<\/strong> It is the distance travelled by the vehicle in total reaction time, if v is the design speed in m\/s and t is the total reaction time (in sec). Value of \u2018t \u2019 is taken as 2.5 seconds in case of stopping sight distance.
        \nNow, lag distance (d ) = vt metres
        \nIf V is design speed in kmph and t in seconds, then
        \nd = 0.278 Vt metres<\/p>\n

        (ii) Braking Distance (l):<\/strong> It is the distance travelled by vehicle after the application of brakes. It is obtained by equating the work done in stopping the vehicle and kinetic energy stored in the vehicle. Let us consider, F is the maximum frictional force developed and l is the braking distance, then the workdone against friction force in stopping the vehicle will be F l.
        \nwhere, frictional force, F = fW<\/p>\n

        where,\u2018W \u2019 is the total weight of vehicle and \u2018f \u2019 is the coefficient of friction
        \nSo, workdone in stopping the vehicle = fWl<\/p>\n

        \"Lag<\/p>\n

        where, \u2018v\u2019 is design speed in m\/s, \u2018g\u2019 is the acceleration due to gravity in m\/s2<\/sup>, \u2018t\u2019 is the total reaction time in sec and \u2018f\u2019 is coefficient of friction.<\/p>\n

        Overtaking Sight Distance (OSD)<\/h3>\n

        Overtaking is a necessary operation because all the vehicles do not travel with a uniform speed. Overtaking is only possible when driver has sufficient sight distance to complete the whole operation.<\/p>\n

        Overtaking sight distance (OSD) is the minimum distance visible to the driver of a vehicle who is intending to overtake the slow moving vehicle ahead safely against the traffic of opposite direction. It is measured along the centre line of road over which driver with his eye level 1.2 m above the pavement surface can see the top of an object of height 1.2 m above the road surface as shown in Figure.<\/p>\n

        \"<\/p>\n

        Factors affecting the overtaking sight distance:<\/strong><\/h4>\n
          \n
        1. Speed of overtaking vehicles, overtaken vehicle and vehicle coming from opposite direction, if any (the minimum spacing depends on the speeds)<\/li>\n
        2. The spacing between overtaking and overtaken vehicle<\/li>\n
        3. Skill and reaction time of driver<\/li>\n
        4. Rate of acceleration of overtaking vehicle<\/li>\n
        5. Gradient of the road<\/li>\n<\/ol>\n

          Analysis of Overtaking Sight Distance<\/strong><\/h4>\n

          Let us suppose, Vehicle A = Travelling at the design speed of highway
          \nVehicle B = Slow moving vehicle which is going to be overtaken by vehicle A
          \nVehicle C = Travelling in the opposite direction of vehicle A and B
          \nThe whole process of overtaking is split into three parts d1<\/sub>, d2<\/sub> and d3<\/sub>.<\/p>\n

          \"Overtaking<\/p>\n

          Where, d1 = Distance travelled by overtaking vehicle A during the reaction time t sec.
          \nd2<\/sub> = Distance travelled by the vehicle A during the actual overtaking operation in time T seconds.
          \nd3<\/sub> = Distance travelled by the vehicle C coming from the opposite direction.
          \nVb<\/sub> = Speed of the slow moving vehicle (in kmph)<\/p>\n

          The following assumptions are made during calculation of d1 <\/sub>d2<\/sub> and d3<\/sub>.<\/p>\n

            \n
          1. The vehicle A is forced to reduce its speed to the speed of slow moving vehicle (Vb<\/sub>).<\/li>\n
          2. Spacing between vehicle A and vehicle B is s, till there is an opportunity for safe overtaking operation and distance travelled by vehicle A during this reaction time is d1<\/sub>.<\/li>\n<\/ol>\n

            Now \u2018d1<\/sub>\u2019 is the distance travelled by the vehicle A in the reaction time, which is given as<\/p>\n

            d1 <\/sub>= vbt metres<\/p>\n

            Here, value of total reaction time (t) is taken as 2.0 seconds.<\/p>\n

            and, vb = Speed of slow moving vehicle in m\/s<\/p>\n

            Spacing between the vehicle A and B just before the starting of overtaking operation (i.e. at position A2<\/sub> and B1<\/sub>) when both the vehicles moving with the speed of vb<\/sub> m\/s is given by an empirical formula<\/p>\n

            S = 0.7 vb<\/sub> + length of vehicle
            \nGenerally , length of vehicle considered is 6 m<\/p>\n

            S = 0.7 vb<\/sub> + 6 metres …[vb<\/sub> in m\/s]
            \nor S = 0.2 vb<\/sub> + 6 metres …[vb<\/sub> in kmph]<\/p>\n

            Let, \u2018b\u2019 is the distance travelled by vehicle B in the complete overtaking operation time, \u2018T \u2019 sec.<\/p>\n

            b = vbT metres<\/p>\n

            d2 = b + 2S metres …(i)<\/p>\n

            \"Overtaking<\/p>\n

            The values of overtaking sight distance recommended by IRC are given in Table given below.<\/p>\n\n\n\n\n\n
            Overtaking sight distance<\/th>\n<\/tr>\n
            Speed (kmph)<\/strong><\/td>\n40<\/td>\n50<\/td>\n60<\/td>\n65<\/td>\n80<\/td>\n100<\/td>\n<\/tr>\n
            Safe Overtaking Sight Distance (metres)<\/strong><\/td>\n165<\/td>\n235<\/td>\n300<\/td>\n340<\/td>\n470<\/td>\n640<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

            << Previous<\/a> | Next >><\/a>
            \n Must Read: <\/strong>             What is Highway Engineering?<\/strong><\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

            There are certain basic design controls and criteria which govern the geometric features of a highway. Topography Design speed Road<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[921,2],"tags":[924,922,482,923],"class_list":["post-3284","post","type-post","status-publish","format-standard","hentry","category-highway-engineering","category-ce","tag-extrawidening","tag-lag-distance","tag-sight-distance","tag-superelevation"],"_links":{"self":[{"href":"https:\/\/www.madeeasy.in\/study\/wp-json\/wp\/v2\/posts\/3284","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.madeeasy.in\/study\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.madeeasy.in\/study\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.madeeasy.in\/study\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.madeeasy.in\/study\/wp-json\/wp\/v2\/comments?post=3284"}],"version-history":[{"count":0,"href":"https:\/\/www.madeeasy.in\/study\/wp-json\/wp\/v2\/posts\/3284\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.madeeasy.in\/study\/wp-json\/wp\/v2\/media?parent=3284"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.madeeasy.in\/study\/wp-json\/wp\/v2\/categories?post=3284"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.madeeasy.in\/study\/wp-json\/wp\/v2\/tags?post=3284"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}